[. . . ] Printer/Scanner Unit Type 2018 Operating Instructions Printer Reference 2 Setting Up the Printer Driver and Canceling a Print Job Troubleshooting Printer Features Appendix Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the Safety Information in the "Copy Reference" before using the machine. Introduction This manual contains detailed instructions and notes on the operation and use of this machine. For your safety and benefit, read this manual carefully before using the machine. Important Contents of this manual are subject to change without prior notice. [. . . ] If signal quality is poor, remove objects that might cause interference. Note You can check signal status only when using wireless LAN in infrastructure mode. Check using the machine's control panel that the SSID is correctly set. See "Interface Settings/IEEE 802. 11b (Option)", Network Guide. Depending on the access point, client access may be limited by MAC address. Also, check there are no problems in transmission between access point and wired clients, and between access point and wireless clients. 15 Troubleshooting Possible Cause When using wireless LAN, is the LED on the wireless LAN card lit or blinking?Solutions Confirm the orange LED is lit, and the green LED is lit or blinks during transmission. Otherwise, configure [IEEE 802. 11b] in [Interface Settings] in [System Settings]. When using the RPCSTM printer driver on Windows 2000 and connecting with IEEE 1394, an error may occur if you change the option settings on the machine. In this case, follow the procedure below: A Unplug the IEEE 1394 interface cables connected to the compu- 2 ter. B Run the utility tool for the IEEE 1394 interface board, which is stored in the following path on the CD-ROM "Printer Drivers and Utilities". \UTILITY\1394\ Reference For more information about using the utility tool for IEEE 1394, see the README file in the same directory on the CDROM. C Restart the computer. D Connect the computer to the machine using the IEEE 1394 in- terface cables. 16 The Machine Does Not Print Problem Is the Data In indicator blinking or lit after starting the print job?Solutions If not, data is not being sent to the machine. When the machine is connected to the computer using the interface cable Check the machine port settings are correct. · Windows 95/98/Me A Click the [Start] button, point to [Settings], and then click 2 [Printers]. B Click the icon of the machine. On the [File] menu, click [Properties]. C Click the [Details] tab. D In the [Print to the following port:] list, confirm the correct port is selected. · Windows 2000 A Click the [Start] button, point to [Settings], and then click [Printers]. B Click the icon of the machine. D In the [Print to the following port(s)] list, confirm the correct port is selected. · Windows XP Professional and Windows Server 2003 A Click the [Start] button, and then click [Printers and Fax- es]. B Click the icon of the machine. D In the [Print to the following port(s)] list, confirm the correct port is selected. · Windows XP Home Edition A Click the [Start] button, click [Control Panel], click [Print- ers and Other Hardware], and then click [Printers and Faxes]. B Click the icon of the machine. D In the [Print to the following port(s)] list, confirm the correct port is selected. · Windows NT 4. 0 A Click the [Start] button, point to [Settings], and then click [Printers]. B Click the icon of the machine. [. . . ] · Regular · Dark Note Default: Regular 34 Printer Features Parameters Ext. A4 Width You can extend the printing area width (when printing on A4 sheet with PCL). · Off · On Note Default: Off PS Menu Data Format You can select a data format. · Binary · TBCP Limitation This setting is not effective when operating the machine with a parallel, USB, or EtherTalk connection. When the setting is On, the width will be 8/ inches. 3 Append CR to LF By connecting to a host operating system such as UNIX and setting this to on, a carriage return follows each line feed: CR=CR, LF=CR-LF, FF=CR-FF. [. . . ]